How to program chamberlain liftmaster garage door opener

Question

Programming 971LM and 972LM, 371LM and 373LM Security + Transmitter

Table of Contents Show

Programming 971LM and 972LM, 371LM and 373LM Security + Transmitter
Programming the 890MAX and 893MAX Remotes
Models 375LM and 375UT Universal Remotes Programming Instructions for dip switch remotes.
How do I manually program my Chamberlain garage door opener?

Press and release the square colored “Smart” button on your garage door opener motor head in the garage. The Smart button indicator light will glow steady for 30 seconds. Learn buttons are located on the motor head near the terminal strip for wire connections.
While the indicator light is glowing, press and hold the remote button until the lights on the motor head blink or you hear 2 clicks. (about 4 seconds)
Release the remote button and test by pressing again to activate the door.

Programming the 890MAX and 893MAX Remotes

Press and hold the program button on the hand held remote until the LED on the front of the remote turns on.
Press and release the remote control button you with to use the number of times corresponding “Smart” button color on your garage door opener based on the chart below in Chart B:
Exit the remote programming by pressing and releasing any button other than the one you’re programming on the remote.
Go to the garage door motor head and press the “Smart” button.
Press and hold down on the remote control button programmed in Step 2 until the garage door opener lights blink, or 2 clicks are heard, or for 4 seconds. Release and press again to test.

Chart B
# of Presses		Garage Door Opener Type
1		Security + 2.0 (Yellow Learn Button)
2		315 MHz Security + (Purple Learn Button)
3		390 MHz Security + (Red/Orange Learn Button)
4		390 MHz Billion Code (Green Learn Button)

Models 375LM and 375UT Universal Remotes Programming Instructions for dip switch remotes.

Slide open the bottom front of the universal remote shwon to expose the dip swithes and program button. The 375LM can be accessed from the back.
Match the dip switch settings with the settings on your existing remote or the receiver on the ceiling in the garage. To find the receiver look for the floppy antenna wire.
Find and press the Program button on the remote trasmitter until the LED lights up.
Select one of the two remote buttons on this remote and press this button only for the number of times shown in the Chart D, corresponding to your older remote or the receiver in the garage.
Press the program button on the remote to turn off the programming mode.
Test the button programmed to see if it operates your door.

Chart D
# of Presses	Brand	Description
11	Chamberlain	9 dip switches
12	Chamberlain	9 dip switch Canada
13	Genie	12 dip switches
14	Linear Multicode	10 dip switches
15	Chamberlain	8 dip switches
16	Stanley/Multicode	10 dip switches
17	Genie	9 dip switches
18	Linear	8 dip switches
19	Chamberlain	7 position

Fix My Garage Door

If you’ve recently had a LiftMaster garage door opener installed and would like to program your remotes or are replacing lost, broken or stolen remotes, you’ve come to the right place.

Here at Banko Overhead Doors, we have three decades of experience as a Florida leader in garage door installation and service. Our team of professionals put together this handy guide to help you program your LiftMaster garage opener remotes. Simply follow these easy steps:

Step 1: Locate the Learn button on your opener. If you have a wall control, use this button — if not, use the Learn button on your opener. You will need a ladder to access this, so take care when climbing.
Step 2: Press and release the Learn button (press and release twice if your LiftMaster opener is equipped with a MyQ Control Panel).
Step 3: Within 30 seconds, press and hold the button on your remote control that you would like to program for three seconds.
Step 4: Depending on your model of opener and remote, the LED lights will either go out or the opener lights will blink to indicate that the remote has been successfully programmed.
Step 5: Press the programmed button to ensure that it functions properly. If not, repeat the procedure.
Step 6: Repeat the procedure for other buttons or other remotes as necessary.

Programming a remote control is easy with LiftMaster. This high-quality brand of overhead door remote openers is designed for easy and reliable use. If you have trouble programming your remotes, you may have a problem with your remotes or the opener itself.

Our team here at Banko Overhead Doors is always available to inspect and service your garage door and opener, so contact us to schedule a service visit or repair.

Get an Estimate

How do I manually program my Chamberlain garage door opener?

Press and hold the bottom button on the remote control until the blue LED light stays on solid (this will take approximately 15 seconds), then release the button (the blue LED light will stay on for 60 seconds). Press the learn button on your garage door opener for 2-3 seconds, then release it.

program chamberlain liftmaster garage door opener